PCB TOOLS / Electronics reference
BeagleBone Pinout: P8/P9, 1.8 V Analog Inputs and Legacy P6
Look up BeagleBone/Black P8/P9 and early P6, distinguishing header positions, processor balls, multiplexing and voltage domains. Preserve the legacy grid with visible analog-ball corrections and board-specific eMMC/HDMI restrictions.
Quick answer
P8 and P9 each have 46 contacts. Ordinary digital I/O is 3.3 V, not 5 V tolerant; P9 AIN0–6 use the 1.8 V domain. P9.35 is AIN6 at ball A8 and P9.36 AIN5 at B8, not the two source A5 entries. Black does not have the original BeagleBone P6 PMIC header.
Scope
The source names early BeagleBone Rev.6 and Black Rev.5.2. Signal entries are selected pinmux functions, not simultaneously enabled interfaces; R9-style Name entries are SoC balls, not extra header positions. Black eMMC/HDMI consume some pins. Check board revision, device tree and pinmux rather than applying this map to AI, Green or other boards.
Reading example
For AIN0 use P9.39, with analog ground P9.34 and the P9.32 1.8 V domain. Do not apply a 3.3 V sensor output directly to this analog input. I²C2 uses P9.19/20, subject to actual pull-ups and mux configuration.
Legacy tables with visible corrections
BeagleBone and BeagleBone Black boards
| Signal | Name | Pin | Pin | Name | Signal | |
|---|---|---|---|---|---|---|
| GND | 1 | 2 | GND | |||
| GPIO1_6 | R9 | 3 | 4 | T9 | GPIO1_7 | |
| GPIO1_2 | R8 | 5 | 6 | T8 | GPIO1_3 | |
| TIMER4 | R7 | 7 | 8 | T7 | TIMER7 | |
| TIMER5 | T6 | 9 | 10 | U6 | TIMER6 | |
| GPIO1_13 | R12 | 11 | 12 | T12 | GPIO1_12 | |
| EHRPWM2B | T10 | 13 | 14 | T11 | GPIO0_26 | |
| GPIO1_15 | U13 | 15 | 16 | V13 | GPIO1_14 | |
| GPIO0_27 | U12 | 17 | 18 | V12 | GPIO2_1 | |
| EHRPWM2A | U10 | 19 | 20 | V9 | GPIO1_31 | |
| GPIO1_30 | U9 | 21 | 22 | V8 | GPIO1_5 | |
| GPIO1_4 | U8 | 23 | 24 | V7 | GPIO1_1 | |
| GPIO1_0 | U7 | 25 | 26 | V6 | GPIO1_29 | |
| GPIO2_22 | U5 | 27 | 28 | V5 | GPIO2_24 | |
| GPIO2_23 | R5 | 29 | 30 | R6 | GPIO2_25 | |
| UART5_CTSN | V4 | 31 | 32 | T5 | UART5_RTSN | |
| UART4_RTSN | V3 | 33 | 34 | U4 | UART3_RTSN | |
| UART4_CTSN | V2 | 35 | 36 | U3 | UART3_CTSN | |
| UART5_TXD | U1 | 37 | 38 | U2 | UART5_RXD | |
| GPIO2_12 | T3 | 39 | 40 | T4 | GPIO2_13 | |
| GPIO2_10 | T1 | 41 | 42 | T2 | GPIO2_11 | |
| GPIO2_8 | R3 | 43 | 44 | R4 | GPIO2_9 | |
| GPIO2_6 | R1 | 45 | 46 | R2 | GPIO2_7 |
| Signal | Name | Pin | Pin | Name | Signal | |
|---|---|---|---|---|---|---|
| GND | 1 | 2 | GND | |||
| VDD_3V3EXP | 3 | 4 | VDD_3V3EXP | |||
| VDD_5V | 5 | 6 | VDD_5V | |||
| SYS_5V | 7 | 8 | SYS_5V | |||
| PWR_BUT* | 9 | 10 | A10 | SYS_RESETn | ||
| UART4_RXD | T17 | 11 | 12 | U18 | GPIO1_28 | |
| UART4_TXD | U17 | 13 | 14 | U14 | EHRPWM1A | |
| GPIO1_16 | R13 | 15 | 16 | T14 | EHRPWM1B | |
| I2C1_SCL | A16 | 17 | 18 | B16 | I2C1_SDA | |
| I2C2_SCL | D17 | 19 | 20 | D18 | I2C2_SDA | |
| UART2_TXD | B17 | 21 | 22 | A17 | UART2_RXD | |
| GPIO1_17 | V14 | 23 | 24 | D15 | UART1_TXD | |
| GPIO3_21 | A14 | 25 | 26 | D16 | UART1_RXD | |
| GPIO3_19 | C13 | 27 | 28 | C12 | SPI1_CS0 | |
| SPI1_D0 | B13 | 29 | 30 | D12 | SPI1_D1 | |
| SPI1_SCLK | A13 | 31 | 32 | VDD_ADC (1.8V) | ||
| AIN4 | C8 | 33 | 34 | GNDA_ADC | ||
| AIN6 | A8Legacy record: “A5”. The official Black map assigns P9.35/AIN6 to A8; source A5 is incorrect. | 35 | 36 | B8Legacy record: “A5”. The official Black map assigns P9.36/AIN5 to B8, not A5. | AIN5 | |
| AIN2 | B7 | 37 | 38 | A7 | AIN3 | |
| AIN0 | B6 | 39 | 40 | C7 | AIN1 | |
| CLKOUT2 | D14 | 41 | 42 | C18 | GPIO0_7 | |
| GND | 43 | 44 | GND | |||
| GND | 45 | 46 | GND |
| Name | Pin | Pin | Name |
|---|---|---|---|
| BAT | 1 | 2 | BAT |
| BAT_SENSE | 3 | 4 | BAT_TEMP |
| BL_ISET2 | 5 | 6 | BL_ISET1 |
| BL_OUT | 7 | 8 | BL_IN |
| BL_SINK1 | 9 | 10 | BL_SINK2 |
Legacy source notes and applicability
These notes retain the legacy record. For corrected facts and applicability, use this page’s quick answer, scope and visible table corrections.
Expansion Header P8:
Expansion Header P9:
Expansion Header P6 (TPS65217B):
Notes:
BeagleBone Rev. 6 pinout.
All signals on the expansion are 3.3V.
PWR_BUT is a 5V level as pulled up internally by the TPS65217B.
BeagleBone Black Rev. 5.2 pinout.
BeagleBone Black does not include Expansion Header P6.
The LCD pins (P8: 27-46) are used on the BeagleBone Black to drive the HDMI framer.
The eMMC pins (P8: 11-21) can be used to connect eMMC device.
Frequently asked questions
Is A8 a header position?
No. It is an AM335x ball. Wire by header identifiers such as P9.35 and verify the selected mux function.
Can UNO 5 V signals connect directly?
Not by assumption. Black normally uses 3.3 V digital and1.8 V analog domains; design the interface to both endpoints’ specifications.
Related tools and references
Sources and verification
Legacy baseline: the Electrodoc Pro 5.2 data package. Raw records are retained and checked factual corrections are shown explicitly.