PCB TOOLS / Electronics reference
Apple 30-pin Dock legacy pinout
Archive early iPod/iPhone Dock USB, analog A/V, serial and FireWire roles with generation limits.
Quick answer
USB data are 25 (D−)/27 (D+), 23 is the legacy USB 5V supply entry; analog3/4 are right/left outputs.
Scope
These are model-dependent archive entries, not a complete public Apple specification.Generations omit some FireWire charging, line-in or video modes; public MFi sources establish scope/authentication, not each archived contact.
Reading example
For USB data, also identify USB return 16; video aliases8–10 require the exact iPod generation rather than mixing component and S-Video modes.
Legacy tables with visible corrections

| Pin | Name | Description |
|---|---|---|
| 1 | GND | Ground |
| 2 | Audio & Video ground | |
| 3 | Right Out | Line Out Right Ch. |
| 4 | Left Out | Line Out Left Ch. |
| 5 | Right In | Line In Right Ch. |
| 6 | Left In | Line In Left Ch. |
| 7 | (Video Ground) | |
| 8 | Composite Video Out | when slideshow active on iPod Photo |
| Component Video Pb | ||
| 9 | S-Video Chrominance Out | for iPod Color, Photo only |
| Component Video Y | ||
| 10 | S-Video Luminance Out | for iPod Color, Photo only |
| Component Video Pr | ||
| 11 | AUDIO_SW | If connected to GND the iPhone sends audio signals through pin 3-4. |
| GND | Serial Ground | |
| 12 | TX | Serial TXD (device sending) |
| 13 | RX | Serial RXD (device receiving) |
| 14 | n.c. | Reserved |
| 15 | GND | Ground |
| 16 | USB GND | |
| 17 | n.c. | Reserved |
| 18 | 3.3V | 3.3V Power (*) |
| 19 | +12V | Firewire Power +12 VDC |
| 20 | ||
| 21 | Accessory Indicator | Resistor to ground (**) |
| Serial enable | ||
| 22 | TPA - | FireWire Data TPA - |
| 23 | +5V | USB Power +5 VDC |
| 24 | TPA + | FireWire Data TPA + |
| 25 | Data - | USB Data - (***) |
| 26 | TPB - | FireWire Data TPB - |
| 27 | Data + | USB Data + (***) |
| 28 | TPB + | FireWire Data TPB + |
| 29 | GND | FireWire Ground |
| 30 |
Legacy source notes and applicability
These notes retain the legacy record. For corrected facts and applicability, use this page’s quick answer, scope and visible table corrections.
Signals with grey background may not exist on some docking stations.
(*) Stepped up to provide +5 VDC on iPod Camera Connector.
(**) Resistances indicate accessory type:
1kΩ: docking station, beeps when connected
10kΩ: takes some iPods into photo import mode
6.8kΩ: Serial port mode. TX-RX are 3.3V TTL level (requires MAX232 to convert to RS232).
Setting is 8N1 (8 bits, no parity, 1 stop bit), auto-baud range 9600 to 57.6K
68kΩ: iPhone 3g / iPod Touch send audio through line-out without any messages
On the Nano 5G connecting the resistor will disable the audio redirection accomplished by connecting pin 11 to ground.
500kΩ: used to enable serial communications. Used in Dension Ice Link Plus car interface
1MΩ: Belkin auto adaptor, iPod shuts down automatically when power is disconnected.
(***) Pins 25 and 27 may be used in different manner:
To charge an iPhone 3G, 3GS, 4 / iPod Touch 2nd gen, 3rd, 4th or Ipod Classic (6th Gen), usb data- (25) should be at 2.8v, usb data+ (27) should be at 2.0v.
It's also possible to charge iPod and iPhone connecting the +3.3v output (18) to USB Data + (27) through a 47kΩ resistor, and the USB Data- (25) through a 47kΩ resistor to the USB Power source +5v (23). This way the USB function is still useable for normal.
To force the iPod 5G to charge in any case, when USB Power 5 VDC (pin 23) is fed, 25 must be connected to 5V through a 10kΩ resistor, and 27 must be connected to the Ground with a 10kΩ resistor.
To charge iPod Nano pins 25 and 27 should be tied together and then connected to 5V power through to a 10K ohm resistor.
Frequently asked questions
Do all Apple 30-pin devices provide these video modes?
No.The archive distinguishes Photo/Color models; adapters and authentication also affect availability.
Why retain old charging recipes?
To preserve the source with visible limits; they are not implementations validated per model by this site.
Related tools and references
Sources and verification
- Apple MFi: licensed connectors/specification scope
- Apple ExternalAccessory: 30-pin/Lightning communication scope
Legacy baseline: the Electrodoc Pro 5.2 data package. Raw records are retained and checked factual corrections are shown explicitly.