PCB TOOLS / Electronics reference
USB Power, Data Rates and Legacy PD Profiles
Separate enumeration current, Type-C current advertisement, USB PD negotiation and physical signaling rates, with explicit legacy PD-profile scope.
Quick answer
USB-C describes a connector, not a guaranteed speed or power. Traditional 100/500 mA and 150/900 mA values have their own bus conditions. Type-C 1.5/3 A needs the specified CC advertisement; higher PD voltages/powers require compatible source, sink and cable negotiation.
Scope
Four tables and 25 rows remain. Profiles 0–5 are labeled legacy USB PD 1.0, not the complete modern PD system. Archived AWG/length values do not guarantee data performance or arbitrary power conditions. Signaling Gb/s is not application throughput in GB/s.
Reading example
1.5 Mbit/s divided by eight is 0.1875 MB/s or 187.5 kB/s decimal, before protocol overhead; the original 192 KB/s is corrected. PD EPR 48 V ×5 A=240 W is a negotiated-capability example, not a property of every USB-C port.
Checked reference tables
| Capability | Value | Required conditions |
|---|---|---|
| USB PD EPR | 48 V × 5 A = 240 W | Successful EPR negotiation among capable source, sink and qualified cable; not a default output. |
| USB4 v2 | 80 Gbit/s | Symmetric signaling capability requires a compatible complete link. |
| Optional asymmetric USB4 v2 | 120 / 40 Gbit/s | Up to 120 in one direction and 40 in the other, not 120 both ways. |
Legacy tables with visible corrections
USB Power Specification
| Mode | USB 2.0 | USB 3.x | ||
|---|---|---|---|---|
| Current Max | Vbus tolerance | Current Max | Vbus tolerance | |
| Low-power bus powered | 100mA | 4.40V - 5.25V | 150mA | 4.00V - 5.25V |
| High-power bus powered | 100mA | 4.40V - 5.25V | 150mA | 4.00V - 5.25V |
| 500mA | 4.75V - 5.25V | 900mA | 4.00V - 5.25V | |
| Self-powered | 100mA | 150mA | ||
| Suspend | 2.5 mA (USB 2.0, 2008 ECN; InterChip separate)Legacy record: “500uA”. The original 500 µA predates the USB-IF ECN changing the general peripheral limit to 2.5 mA. | 2.5mA | ||
USB Power Delivery Specification
| Profile | Supplying capability | Max Power |
|---|---|---|
| 0 | reserved | - |
| 1 | 5V @ 2A | 10 W |
| 2 | 5V @ 2A, 12V @ 1.5A | 18 W |
| 3 | 5V @ 2A, 12V @ 3A | 36 W |
| 4 | 5V @ 2A, 12V, 20V @ 3A | 60 W |
| 5 | 5V @ 2A, 12V, 20V @ 5A | 100 W |
USB Speed Specification
| Mode/Name | Data Rate | Tolerance |
|---|---|---|
| Low speed | 1.5 Mbit/s (raw rate ÷8=187.5 kB/s, before overhead)Legacy record: “1.5Mb/s (192KB/s)”. Decimal bit/byte conversion does not give the archived 192 KB/s. | ±1.5% or 15,000ppm |
| Full speed | 12Mb/s (1.5MB/s) | ±0.25% or 2,500ppm |
| High speed (USB 2.0) | 480Mb/s (60MB/s) | ± 500ppm |
| USB 5Gbps, SuperSpeed 5Gbps (USB 3.0, USB 3.1 Gen1, USB 3.2 Gen1x1) | 5Gb/s (0.5GB/s) | ± 600ppm |
| USB 10Gbps, SuperSpeedPlus, SuperSpeed 10Gbps (USB 3.2 Gen1x2) | 10Gb/s (1.0GB/s) | |
| USB 10Gbps, SuperSpeedPlus, SuperSpeed 10Gbps (USB 3.1 Gen2, USB 3.2 Gen2x1) | 10Gb/s (1.2GB/s) | |
| USB 20Gbps, SuperSpeed 20Gbps (USB 3.2 Gen2x2) | 20Gb/s (2.4GB/s) | |
| USB 40Gbps (USB 4.0 v1) | 40Gb/s | |
| USB 80Gbps (USB 4.0 v2) | 80Gb/s |
USB 2.0 Cable Specification
| AWG | Max length |
|---|---|
| 28 | 0.81 m |
| 26 | 1.31 m |
| 24 | 2.08 m |
| 22 | 3.33 m |
| 20 | 5.00 m |
Legacy source notes and applicability
These notes retain the legacy record. For corrected facts and applicability, use this page’s quick answer, scope and visible table corrections.
USB 3.1 Type-C connector supports higher power devices (5V @ 1.5A, 3A).
Decoupling capacitance between VBUS and ground on devices:
- Maximum is 10uF to limit inrush current.
- Minimum is 1uF to limit flyback voltage on disconnection.
USB Power Delivery Specification
USB Speed Specification
USB 2.0 Cable Specification
Data wire size:
Shielded → 28 AWG twisted,
Non-shielded → 28 AWG non-twisted
Power wire size:
Frequently asked questions
Does USB 80Gbps imply 120Gbps in every direction?
No. USB4 v2 120/40 Gbit/s is an optional asymmetric configuration requiring compatible capabilities. Symmetric signaling is up to 80 Gbit/s.
Does the AWG table guarantee a five-meter USB4 cable?
No. It is an archived USB 2.0 power-wire reference. Gauge alone does not determine high-speed loss, certification, active electronics or usable length.
Related tools and references
Sources and verification
- USB-IF: suspend-current ECN and capacitance update status
- USB-IF: PD 3.1 EPR up to 240 W
- USB-IF: 80 Gbps and optional 120/40 Gbps
Legacy baseline: the Electrodoc Pro 5.2 data package. Raw records are retained and checked factual corrections are shown explicitly.