PCB TOOLS / Electronics reference
Electrical Resistivity, Conductivity and Temperature Coefficient Table
Look up material resistivity ρ, conductivity σ and linear temperature coefficient α near 20°C, with units, material-condition limits and source-data consistency notes.
Quick answer
For the same material, condition and temperature, ρ=1/σ and a uniform conductor has R=ρL/A. The source copper reference is ρ=1.68×10⁻⁸ Ω·m and σ≈5.95×10⁷ S/m. Graphene, graphite and amorphous carbon are distinct entries, not one generic graphite value.
Scope
These are approximate references, not guaranteed values for a grade, batch, doping, humidity or processing condition. Use R(T)=R(T₀)[1+α(T−T₀)] only over a suitable limited range; large temperature changes, semiconductors, insulators and phase transitions require specific data.
Reading example
For copper with ρ=1.68×10⁻⁸ Ω·m, L=10 m and A=1 mm²=10⁻⁶ m², R=0.168 Ω. Using α=0.0039/°C only as a local linear example near 20°C gives about 0.174552 Ω at 30°C.
Checked reference tables
| Input or operation | Value | Meaning |
|---|---|---|
| Source ρ range | (1.3–3.3)×10¹⁶ Ω·m | Not validated by this calculation |
| Arithmetic reciprocal 1/ρ only | (3.03–7.69)×10⁻¹⁷ S/m | Reciprocal endpoints reverse order; not a new measured σ |
| Original σ range | (3–8)×10⁻¹⁵ S/m | Cannot be paired with source ρ as exact consistent data |
Legacy tables with visible corrections
Resistivity and Temperature Coefficient at 20°C (68°F)
| Material | Resistivity ρ (Ω·m) | Temp. coefficient α (per °C) | Conductivity σ (S/m) | ||
|---|---|---|---|---|---|
| Carbon (graphene) | 1.0 | x10⁻⁸ | -0.0002 | 1.0 | x10⁸ |
| Silver | 1.59 | x10⁻⁸ | 0.003819 | 6.29 | x10⁷ |
| Copper | 1.68 | x10⁻⁸ | 0.0039 | 5.95 | x10⁷ |
| Gold | 2.44 | x10⁻⁸ | 0.0034 | 4.10 | x10⁷ |
| Aluminium | 2.82 | x10⁻⁸ | 0.0039 | 3.5 | x10⁷ |
| Calcium | 3.36 | x10⁻⁸ | 0.0041 | 2.98 | x10⁷ |
| Tungsten | 5.6 | x10⁻⁸ | 0.0045 | 1.79 | x10⁷ |
| Zinc | 5.9 | x10⁻⁸ | 0.0037 | 1.69 | x10⁷ |
| Nickel | 6.99 | x10⁻⁸ | 0.0060 | 1.43 | x10⁷ |
| Lithium | 9.28 | x10⁻⁸ | 0.0060 | 1.08 | x10⁷ |
| Iron | 9.71 | x10⁻⁸ | 0.005671 | 1.03 | x10⁷ |
| Platinum | 1.06 | x10⁻⁷ | 0.003927 | 9.43 | x10⁶ |
| Tin | 1.09 | x10⁻⁷ | 0.0045 | 9.17 | x10⁶ |
| Gallium | 1.40 | x10⁻⁷ | 0.004 | 7.10 | x10⁶ |
| Lead | 2.2 | x10⁻⁷ | 0.0039 | 4.55 | x10⁶ |
| Titanium | 4.2 | x10⁻⁷ | ... | 2.38 | x10⁶ |
| Manganin | 4.82 | x10⁻⁷ | 0.000002 | 2.07 | x10⁶ |
| Constantan | 4.9 | x10⁻⁷ | 0.000008 | 2.04 | x10⁶ |
| Stainless steel | 6.90 | x10⁻⁷ | 0.00094 | 1.45 | x10⁶ |
| Mercury | 9.8 | x10⁻⁷ | 0.0009 | 1.02 | x10⁶ |
| Nichrome (Ni,Fe,Cr) | 1 | x10⁻⁶ | 0.0004 | 1 | x10⁶ |
| Kanthal (Fe,Cr,Al) | 1.2-1.5 | x10⁻⁶ | ... | ... | ... |
| Carbon (graphite) | 3-60 | x10⁻⁵ | -0.0005 | ... | ... |
| Carbon (amorphous) | 5-8 | x10⁻⁴ | -0.0005 | 1.25-2 | x10³ |
| Germanium | 4.60 | x10⁻¹ | -0.048 | 2.17 | x10⁰ |
| Sea water | 2.00 | x10⁻¹ | ... | 4.8 | x10⁰ |
| Silicon | 0.1-60 | ... | -0.075 | ... | .. |
| Glass | 1-10⁴ | x10⁹ | ... | ... | ... |
| Hard rubber | 1-100 | x10¹³ | ... | 1 | x10⁻¹⁴ |
| Air | 1.3-3.3 | x10¹⁶ | ... | Source ρ/σ inconsistentLegacy record: “3-8”. Source air ρ=(1.3–3.3)×10¹⁶ Ω·m and σ=(3–8)×10⁻¹⁵ S/m have an approximately two-order reciprocal inconsistency without validated conditions. Do not pair the original σ with that ρ. The additional table demonstrates 1/ρ arithmetic only, without validating either material value. | Not a paired value; see noteLegacy record: “x10⁻¹⁵”. Source air ρ=(1.3–3.3)×10¹⁶ Ω·m and σ=(3–8)×10⁻¹⁵ S/m have an approximately two-order reciprocal inconsistency without validated conditions. Do not pair the original σ with that ρ. The additional table demonstrates 1/ρ arithmetic only, without validating either material value. |
| Quartz (fused) | 7.5 | x10¹⁷ | ... | 1.3 | x10⁻¹⁸ |
| PET | 10 | x10²⁰ | ... | 1 | x10⁻²¹ |
Legacy source notes and applicability
These notes retain the legacy record. For corrected facts and applicability, use this page’s quick answer, scope and visible table corrections.
Ω=V/A
S=Ω⁻¹=A/V
Electrical resistivity and conductivity:
ρ=1/σ
ρ=R·A/l
Temperature coefficient:
R(T)=R(T_0)(1+α·ΔT)
Frequently asked questions
How does resistivity differ from resistance?
Resistivity ρ, in Ω·m, describes a material under specified conditions. Resistance R, in Ω, also depends on length and area. Convert mm² to m² before using SI formulas.
Can a negative temperature coefficient be extrapolated indefinitely?
No. α generally approximates behavior locally near its reference temperature. Larger changes can be nonlinear; a zero or negative resistance from the linear expression signals an invalid extrapolation.
Related tools and references
Sources and verification
- OpenStax: resistivity, conductivity, geometry and temperature relations
- NBS/NIST: copper resistivity, temperature and material condition
Legacy baseline: the Electrodoc Pro 5.2 data package. Raw records are retained and checked factual corrections are shown explicitly.